All posts

The Running Toilet: Fix It Yourself in 20 Minutes

A running toilet usually comes down to one of three cheap, easy-to-replace parts. Here's how to diagnose and fix it yourself before you pay anyone a service call.

·Maintenance, Plumbing

A running toilet is one of the most common calls we get — and one of the few plumbing problems we'll tell you outright not to pay us for. It's almost always a cheap part, a basic skill, and about 20 minutes of your evening. We'd rather you fix it yourself and trust us when something actually requires a plumber than have you book a service call for a $10 flapper.

Here's how to find the cause and fix it, in order from most to least likely.

First, figure out what "running" actually means

Toilets run for one of two basic reasons: water is continuously leaking from the tank into the bowl, or the fill valve keeps topping off the tank because it's not shutting off at the right level. Almost every cause traces back to one of three parts inside the tank, all of which are inexpensive and don't require any special tools.

Take the lid off the tank before you do anything else. You'll be looking at three components: the flapper (a rubber or silicone seal at the bottom, covering the drain), the fill valve (the taller assembly, usually on the left, that refills the tank), and the float (attached to the fill valve, it rises with the water level and tells the valve when to stop).

1. A worn or warped flapper

This is the most common cause by a wide margin. The flapper seals the tank's drain hole between flushes. Over years of use, rubber flappers degrade — they warp, crack, or develop a mineral coating that keeps them from sealing flush against the valve seat. Even a slightly imperfect seal lets water seep continuously into the bowl, which the fill valve then tries to replace, creating a cycle that sounds like running or intermittent refilling.

Check it yourself: Drop a few drops of food coloring into the tank (not the bowl) and wait 10–15 minutes without flushing. If color shows up in the bowl, water is leaking past the flapper.

Fix it yourself: Shut off the water supply valve behind the toilet, flush to empty the tank, and unhook the old flapper from the pegs or flush valve overflow tube. Take it with you to a hardware store to match it — flappers vary slightly by brand and valve seat size — and snap the new one into place. Turn the water back on and test. This step alone takes about 10 minutes and the part typically costs less than $10.

2. A float set too high

If the float is positioned too high, the tank fills past the top of the overflow tube, and the excess water drains continuously down that tube into the bowl — which looks and sounds exactly like a running toilet, even with a perfectly good flapper.

Check it yourself: Look at the water level in the tank relative to the top of the overflow tube (the vertical tube in the center). The water line should sit about an inch below the top of that tube. If it's at or above it, the float is set too high.

Fix it yourself: On most modern fill valves, there's a small screw or clip on the float arm, or a float cup that slides up and down the valve shaft. Adjust it down slightly, flush, and recheck the water level. This takes a couple of minutes and costs nothing.

3. A worn fill valve

If the flapper seals properly and the float is set correctly but the toilet still runs — especially with a faint hissing sound — the fill valve itself may have worn internal seals and isn't shutting off completely.

Check it yourself: With the tank full and the toilet not recently flushed, listen closely at the fill valve. A steady hiss or trickle means it isn't closing all the way.

Fix it yourself: Fill valves are a slightly bigger job than a flapper, but still well within DIY range. Shut off the water, drain the tank, disconnect the supply line and the old valve (it unscrews from the bottom of the tank), and install a new one following the package instructions — they're largely universal and cost $10–$20. Reconnect the supply line, turn the water back on, and adjust the float to the correct height. Budget closer to 20 minutes for this one, mostly because of the supply line connection.

Working through it in order

  1. Lift the tank lid and look at the three components.
  2. Run the food-coloring test for a flapper leak.
  3. Check the water level against the overflow tube.
  4. Listen for hissing with a full, undisturbed tank.
  5. Replace the flapper first if you're not sure — it's the cheapest, easiest, and most likely fix.

Most running toilets resolve at step 2. If you've replaced the flapper and adjusted the float and it's still running, move on to the fill valve before assuming anything more complicated is wrong.

When it's not one of these three things

Occasionally a running toilet points to something bigger — a cracked overflow tube, a corroded tank bolt causing a slow leak at the base, or a supply line issue. If you've swapped the flapper and fill valve and adjusted the float and the problem persists, that's the point where it's worth calling a plumber rather than guessing further.

We'd rather you know what's a $10 fix

Giving away the easy stuff is part of how we think about trust. A running toilet almost never needs a service call, and we'd rather tell you that directly than have you book one. If you've worked through all three steps above and it's still running, or you'd rather not take the tank apart yourself, our plumbing team handles it quickly across Seattle, Bellevue, Kirkland, Bothell, Mercer Island, Issaquah, Sammamish, and Redmond. Reach out through /contact or call (425) 999-1091.

Call 24/7Request a Walkthrough