All posts

Low Water Pressure: The Five Usual Suspects

Weak water pressure has a short list of common causes. Here's how to work through them in order, what you can check yourself, and when the fix belongs to a plumber.

·Plumbing, Maintenance

Low water pressure rarely announces its cause. It just shows up — a shower that used to feel strong now trickles, or a kitchen faucet that fills a pot in twice the time it used to. Homeowners usually assume it's something dramatic, but in our experience it's almost always one of a handful of familiar problems. Here's how to work through them in order, starting with what you can check yourself.

First, confirm it's actually a pressure problem

Before troubleshooting, figure out whether the issue is isolated to one fixture or affects the whole house. Turn on a few faucets in different rooms, including one on a different floor if you have one. If only one fixture is weak, the problem is almost certainly local to that fixture or the line feeding it — not your home's overall pressure. If everything is weak, you're dealing with one of the whole-house causes below.

1. A clogged or scaled aerator or showerhead

This is the most common cause, and the easiest to fix. Faucet aerators and showerheads have small screens that trap mineral deposits over time, especially with the harder water found in parts of the Puget Sound region. A clogged aerator can make a fixture feel like the whole house has low pressure when it's really just that one opening.

Check it yourself: Unscrew the aerator or showerhead, inspect it for white or greenish mineral buildup, and soak it in vinegar for a few hours. Clean out any debris with an old toothbrush and reinstall. If pressure improves at that fixture immediately, that was the problem.

DIY or pro: DIY, every time. This takes ten minutes and costs nothing.

2. A partially closed shutoff valve

Every fixture, and the house as a whole, has a shutoff valve somewhere upstream — under the sink, behind the toilet, or at the main line near your water meter. If a valve got bumped, or wasn't fully reopened after recent work, it can restrict flow without shutting it off entirely, which is a confusing kind of partial failure.

Check it yourself: Trace the line back to the nearest shutoff and make sure it's turned fully open. If the whole house seems low, check the main shutoff valve and the valve at the meter.

DIY or pro: DIY. This is a two-minute check that's worth doing before assuming anything more complicated is wrong. If you're not sure where your main shutoff is, that's worth fixing regardless of what's causing your current pressure issue — knowing its location before an emergency matters.

3. Corroded or scaled galvanized pipe

If your home has original galvanized steel plumbing — common in homes built through the 1960s — mineral buildup and rust inside the pipe narrows its interior diameter over decades. This shows up as a gradual, whole-house pressure decline rather than a sudden drop, and it often comes with a rusty or brownish tint to the water, especially after the house has sat unused for a few hours.

We've covered this pipe material in more depth in our post on galvanized and polybutylene pipes in older Puget Sound homes, including what the corrosion actually looks like and why it doesn't reverse itself.

Check it yourself: You can observe the symptoms, but you can't fix the cause. If water runs brown or rusty and pressure has been fading for months or years rather than days, galvanized pipe is a reasonable suspect.

DIY or pro: Pro. This isn't a cleaning job — it's a pipe condition that a plumber needs to evaluate directly, and depending on how widespread it is, the conversation may move toward repair versus a larger repiping project.

4. A failing pressure regulator

Many homes, especially those on municipal water with higher incoming pressure, have a pressure-reducing valve (PRV) installed where the main line enters the house. PRVs wear out like any mechanical component, and when they fail, they sometimes fail toward too little pressure rather than too much — the opposite of what most homeowners expect from a "broken" valve.

Check it yourself: If your home has a PRV, it's usually a bell-shaped fitting on the main line near where it enters the house. Beyond visually confirming it's there and not visibly damaged, this isn't something to test or adjust yourself — PRVs are calibrated components, not comfort-level dials.

DIY or pro: Pro. A plumber can test actual incoming pressure with a gauge, which tells you definitively whether the regulator itself is the problem or whether the restriction is happening somewhere else in the line.

5. A hidden leak

A leak anywhere in your supply line — inside a wall, under a slab, or in the yard between the meter and the house — diverts water away from your fixtures, which shows up as reduced pressure at every tap. This is the least common of the five, but it's the one with the highest cost of waiting, since a leak that's dropping your pressure is also a leak that's actively damaging something.

If you've noticed a pressure drop alongside an unexplained jump in your water bill, that combination points toward a leak rather than pipe scale or a valve issue. Our post on tracking down a hidden leak from a water bill spike walks through how to narrow down where it might be.

Check it yourself: You can check your water meter during a period when nothing in the house is using water — if it's still moving, something is leaking somewhere. Pinpointing the exact location, though, usually requires equipment and experience you won't have on hand.

DIY or pro: Pro, and sooner rather than later. A leak that's affecting your pressure has likely been running for a while already.

Working through the list in order

If you're dealing with low pressure right now, the efficient path is to rule out the cheap, fast explanations first:

  1. Clean the aerator or showerhead at the affected fixture.
  2. Check nearby and main shutoff valves for partial closure.
  3. Note whether the drop is sudden or gradual, and whether water looks discolored.
  4. If it's whole-house and gradual, suspect pipe condition or a regulator.
  5. If it's whole-house and comes with a rising water bill, suspect a leak.

The first two items take minutes and solve the problem more often than homeowners expect. The last three are worth a call rather than a guess, because misdiagnosing a pipe or leak issue tends to cost more in wasted time than the service call would have.

Getting a straight answer

If you've ruled out the aerator and the valves and pressure is still off, our plumbing team can pressure-test your system, check your regulator, and identify whether you're dealing with pipe condition, a leak, or something else — across Seattle, Bellevue, Kirkland, Bothell, Mercer Island, Issaquah, Sammamish, and Redmond. Reach out through /contact or call (425) 999-1091 to get it diagnosed properly instead of guessing.

Call 24/7Request a Walkthrough